Product Data Sheet
|07 27 26|
DATA SHEET 6384-000
Liquid Membrane Thin Film Permeable Air Barrier
AIR-SHIELD TMP is a water-based air/liquid moisture barrier that cures to form a tough, seamless, elastomeric membrane. AIR-SHIELD TMP exhibits excellent resistance to air leakage. When properly applied as a drainage plane, AIR-SHIELD TMP prohibits liquid water intrusion into the substrate.
AIR-SHIELD TMP has been specifically formulated to act as an air and liquid moisture barrier, allowing vapour to pass through it. It may be applied to most common surfaces and integrated into various wall systems. AIR-SHIELD TMP is suitable for both new construction and retrofit applications.
- High permeability – allows the transmission of moisture vapour through porous building materials.
- Highly flexible – bridges cracks, which may form in the substrate.
- UV resistant – can be left exposed up to six months.
- User friendly – single-component, water-based technology allows for simple, safe application and easy clean up.
- Liquid applied – simplifies detailing and assures a monolithic, seamless membrane when applied to a rough or smooth surface.
- Sprayable – with appropriately configured airless spray equipment – low application costs.
- Excellent adhesion – remains firmly bonded to the substrate, even when applied over damp surfaces.
18.93 Litre (5 Gallon) Pails
208.20 Litre (55 Gallon) Drums
|Plywood||2.45 m2/L (100 ft.2/gal.)|
|Exterior Gypsum Sheathing||2.45 m2/L (100 ft.2/gal.)|
|Wet Film Thickness||10 – 31 Mils|
|Cured Film Thickness||6 – 18 Mils|
|CMU Substrate||1.47 m2/L (60 ft.2/gal.)|
|Wet Film Thickness||20 – 41 Mils|
|Cured Film Thickness||12 – 24 Mils|
Coverage dependent on substrate type, weather, and application conditions.
When stored indoors in original, unopened containers at temperatures between 4° – 32° C, optimum performance and best use is obtained within one year of date of manufacture.
- Meet requirements of 2015 National Building Code for Air Barriers
- ASTM E84, Class A
- ASTM E2178
- ASTM E2357
- Complies with Canada VOC Concentration Limits for Architectural Coatings Regulations
|Solids Content, %:||58|
|Flexibility @ -26° C, ASTM C836:||PASS|
|Elongation (ASTM D412), %:||1000|
|Water Vapor Permeance|
(ASTM E96, Procedure B) Perms:
|Service Temperature:||Not to exceed 80° C|
|Nail Sealability (ASTM D1970):||Pass|
|Storage Temperature||4° – 32° C|
(At Time of Application):
|-6.7° C and rising|
|Test Method||ASTM E2178-01||ASTM E2357|
|ABAA Requirements||0.02 L/S/M2|
|AIR-SHIELD TMP Results:||<0.02 L/S/M2|
*Independent test available upon request
AIR-SHIELD TMP may be used in NFPA 285 complying wall assemblies. Contact W. R. MEADOWS for further information.
Surface Preparation … All surfaces must be clean (free of all coatings and curing compounds), free of frost, structurally sound, and relatively smooth. Prepare substrate per manufacturer’s instruction prior to membrane application. All walls to receive AIR-SHIELD TMP must be capped to prevent moisture infiltration from entering the wall during construction.
Exterior Sheathing Panels … Exterior sheathing panels are to be installed and fastened per manufacturer’s recommendation. For detailed application information, see INSTALLATION INSTRUCTIONS: JOINT TREATMENT OF EXTERIOR SHEATHING PANELS WHEN USING AIR-SHIELD TMP. For joint treatment in plywood and OSB sheathing, please see PLYWOOD SHEATHING JOINT DETAIL INSTALLATION GUIDELINES.
Rough Openings … Refer to AIR-SHIELD ROUGH OPENING INSTALLATION GUIDELINES for recommendations.
Concrete Masonry Units … Before applying AIR-SHIELD TMP to CMU surfaces, patch all cracks, protrusions, small voids, offsets, details, irregularities, and small deformities with MEADOW-PATCH® 5 or MEADOW-PATCH 20 at least two hours before application. All mortar joints should be full and struck flush with the face of the CMU.
Temperature/Conditions … Curing/drying times are dependent on air temperature, airflow, relative humidity, substrate temperature, wind chill, dew point and etc. For example, as the temperature decreases or the humidity increases, the dry time will increase. If the temperature drops below 4.5° C, the cure rate, dry time, and rain/snow resistance will be delayed. Protect membrane from rain and washout prior to drying. Exposure to air temperatures/wind chills below -6.6° C during curing may lead to cracking and decrease of performance of AIR-SHIELD TMP.
Tack-Free Time: 2 hours
Full Cure: 48 hours
Roller … AIR-SHIELD TMP can be applied directly from the container; a 19.1 mm (¾”) nap roller is recommended. Apply AIR-SHIELD TMP on a vertical surface, in multiple coats if necessary, to achieve a final film thickness of 10 mils wet (6 mils dry). NOTE: While the proper film thickness may be achieved with a single coat, multiple coats may be necessary if the material slumps due to temperature and/or substrate conditions. Allow each previous coat to dry (approximately one hour) prior to applying the next coat.
Sprayer … AIR-SHIELD TMP should be stored and maintained at a temperature of 4.4° C or higher throughout the entire spray application. The product will become thick and difficult to spray at temperatures below 15.6° C. Note: Use of Graco HydraMax 350 or Graco GH833 is recommended for optimum performance. A Graco heavy duty texture gun with either a 0.051″ (Graco GHD 551), 0.035″ (Graco GHD 535), or 0.037″ (Graco GHD 537) spray tip is recommended. If cratering occurs, the GHD 535 or 537 is recommended for a smoother finish. Spray AIR-SHIELD TMP on a vertical surface to achieve a final film thickness of 10 mils wet (6 mils dry). NOTE: While the proper film thickness may be achieved with a single coat, multiple coats may be necessary if the material slumps due to temperature and/or substrate conditions. Allow each previous coat to dry (approximately one hour) prior to applying the next coat. Porous substrates, masonry blocks, etc., may require multiple coats to achieve recommended film thickness.
Cleanup … Material should not be left in the pump, lines, or gun when finished spraying. After spraying, flush water through the system until pump and hose are clear [approximately 3.78 L (5 gal.)] Aromatic solvents, such as xylene or toluene [approximately 7.6 L (2 gal.)], can be used for final flushing after water is flushed through the pump and lines. Water should be flushed through the machine to remove any solvent prior to spraying of AIR-SHIELD TMP.
DO NOT FREEZE. Keep containers tightly sealed. Do not apply AIR-SHIELD TMP if rainfall is forecast or imminent within 12 hours of application.
HEALTH AND SAFETY
Direct contact may result in mild irritation to the skin and eyes. Should adverse effects occur, remove subject from area immediately. If irritation occurs and persists, move victim from exposure source and treat symptomatically. Flush affected areas with mild soap and water. Refer to Safety Data Sheet for complete health and safety information.
MASTERFORMAT NUMBER AND TITLE
07 27 26 – Fluid-Applied Membrane Air Barriers
May help contribute to LEED credits:
- EAp2: Minimum Energy Performance
- EAc2: Optimize Energy Performance
- MRc9: Construction and Demolition Waste Management
- EQc2: Low-Emitting Materials [For Healthcare and Schools (exterior-applied products) ONLY]