Product Data Sheet
|07 17 16||DATA SHEET 5126-000|
Water-Based Acrylic Adhesive
CLAY-TITE ADHESIVE is a water-based, acrylic adhesive containing emulsified bentonite. It is easy to apply using a trowel or putty knife. The product bonds strongly to various substrates, including concrete and waterproofing membranes, such as CLAY-TITE from W. R. MEADOWS.
CLAY-TITE ADHESIVE is used to fill cracks and voids in walls and pipe penetrations, to fill inside corners between vertical and horizontal transitions, to fill voids and adhere WATERSTOP EC from W. R. MEADOWS to construction joints, and to seal joints and overlaps in applications of CLAY-TITE. CLAY-TITE ADHESIVE forms a strong adhesive barrier, helping create a seamless installation for these products. For installations with shotcrete or lagging, CLAY-TITE ADHESIVE protects CLAY-TITE from damage caused by this type of application.
- Easy to apply.
- Bonds strongly to various substrates.
- Ensures a complete, seamless CLAY-TITE waterproofing installation.
- Also compatible with WATERSTOP EC.
887 mL (30 Oz.) Cartridges (9/Carton)
7.6 L (2 Gal.) Units
18.9 L (5 Gal.) Pails
When stored indoors in original, unopened containers at temperatures between 4° – 32° C, optimum performance and best use is obtained within two years of date of manufacture.
|Physical Properties||Test Method||Value|
|Flow, Sag, Slump||ASTM 2202||100 mm
|Sodium Bentonite||–||15 – 20% by Weight
[0.16 kg/L (1.3 Lb./Gal.)
|Solids by Weight||–||40%|
|VOC||ASTM D3960-92||0 g/L|
|Tack-Free Time||Field Testing||30 mins|
|Full-Cure Time||–||12 – 24 hrs|
|Installation Temperatures||ASTM D746||0˚ – 50˚ C|
|Adhesive Strength||ASTM D1004||100 N (25 lb.)|
|% Elongation at Break||ASTM D412||125%|
|Hardness||ASTM D2240 Procedure A||~90 Shore A|
|ASTM D751 Procedure A||30 m (100′) of water|
|Vapor Permeability||ASTM D5084||1 x 10-9 cm per sec|
|Functional Temperatures||ASTM D746||-25˚ to 50˚C|
CLAY-TITE Application Method … For detailed instructions, refer to CLAY-TITE BLINDSIDE INSTALLATION GUIDELINE. Guidelines are available for blindside, backfilled wall, and underslab applications.
WATERSTOP EC Surface Preparation … Surface must be free of all debris and standing water. Dusty, damp, or uncured surfaces are suitable for application.
WATERSTOP EC Application Method … On smooth surfaces. Apply a bead at 3.2 – 6.4 mm (1/8″ – 1/4″) along the joint. On non-smooth surfaces, knock down protrusions greater than 12.7 mm (1/2″) and use CLAY-TITE ADHESIVE to fill voids. Apply WATERSTOP EC into uncured CLAY-TITE MASTIC and nail every 381 mm (15″) o.c. with powder-actuated or hand-driven concrete nails (2.54 cm or 1″ shank) with washer (15 – 23 mm or 5/8″ – 13/16″r). Butt ends and fill gap between adjacent pieces for a continuous application.
Cleanup … Use soap and water on uncured material.
Protect from moisture. Do not freeze.
MASTERFORMAT NUMBER AND TITLE
07 17 16 – Bentonite Composite Sheet Waterproofing
May help contribute to LEED credits:
- MRc9: Construction and Demolition Waste Management
- EQc2: Low-Emitting Materials [For Healthcare and Schools (exterior-applied products) ONLY]