ULTRITE Degreaser is a heavy duty concrete degreaser and stripper, which will biodegrade. It naturally and safely replaces mineral spirits and chlorinated solvent type heavy-duty concrete degreaser products.
Product Data Sheet
|03 01 30.51|
DATA SHEET 3910-101
Heavy-Duty Concrete Degreaser and Stripper
ULTRITE Degreaser is a heavy duty concrete degreaser and stripper, which will biodegrade. It naturally and safely replaces mineral spirits and chlorinated solvent type heavy-duty concrete degreaser products..
ULTRITE DEGREASER penetrates concrete surfaces on contact to soften, lift, and remove a wide range of oils, polymers, fats and greases. Use ULTRITE DEGREASER to remove dirt, tire marks, oil spills, grease and other contaminants. It will also remove most curing compounds and cure/seals from concrete floors. Periodic stripping of concrete floors is in keeping with good concrete maintenance practices. It is ideal for use in warehouses, industrial plants, food processing plants, schools, automotive plants, parking garages, plazas and service stations . . . anywhere cleaning and stripping of concrete surfaces is required.
|Packaging||208 litre drum (55 U.S. gal.)|
18.9 litre pails (5 U.S. gal.)
3.78 litre cans (1 U.S. gal.)
|Coverage||Stripping/Degreasing/Heavy-Duty Cleaning: 2.5 – 4.9 m²/L (100-200 ft.²/gal.)|
|Shelf Life||1 year in unopened, unused container|
- Both a stripper and a degreaser in one.
- Ready and easy to use full-strength directly from the container.
|Appearance||Clear, Light Yellow|
|Weight/3.8 litres (U.S. gallon)||3.6 kg (7.95 lbs.)|
|Flash Point||54°C (130°F)|
|Solubility, in water||Excellent|
|Rinsability, in water||Excellent|
|*Biodegradable||100% after proper dilution|
*NOTE: When applied and rinsed per W. R. MEADOWS instructions, the material raised from the surface will contain residual amounts of petroleum hydrocarbons. These hydrocarbons are generally very low in concentration and will not have a negative environmental impact on affected soils. Material(s) removed by the ULTRITE DEGREASER will need to comply with local, state and federal disposal requirements.
Use only on masonry or concrete surfaces. Do not use on painted surfaces. Do not use on coloured concrete. DO NOT ALLOW DEGREASER TO DRY OUT. (See Step 2 under Application.)
Application of ULTRITE DEGREASER may depend on the type of curing compound, oil or grease on the surface and in the pores of the concrete.
Note: For severe oil and/or grease stains it may be necessary to follow ACI Guide 515.1R (Section 3.4.2) or the Portland Cement Association (PCA) publication IS214T. These publications outline specific instructions for stain removal, which can be followed by a ULTRITE DEGREASER application. (Copies of these articles may be obtained through your local W. R. MEADOWS representative). A typical application should be as follows:
Apply ULTRITE DEGREASER full strength directly from the container to remove heavy dirt build-up, tire marks, oil spills, grease, hydraulic fluid and any other difficult to remove contaminants from the concrete surface. For normal cleaning applications and for removing curing compounds and cure & seals, apply at full strength to the entire floor. Do not allow ULTRITE DEGREASER in “as applied” form to spill or run-off of the concrete.
Apply ULTRITE DEGREASER and allow it to soften the coating or stain, but DO NOT ALLOW THE SURFACE TO DRY. (Soak times vary, depending on the ambient conditions and the degree of staining on the concrete.) In severe cases, it may be necessary to apply additional ULTRITE DEGREASER to remove stains and/or to prevent the treated area from drying out.
With a stiff bristle brush, or mechanical scrubber, thoroughly scrub the treated area.
Rinse the area with large amounts of clean water. The cleaning action of ULTRITE DEGREASER may be evident by the very light whitish appearance of the initial water rinse. Keep rinsing with water until there is no visible trace of the product or product on the concrete. Disposal of rinse should follow all local, state and federal regulations.
Test patch the dry concrete prior to painting or applying a subsequent surface treatment. If necessary, clean the concrete floor with ULTRITE DEGREASER again until the desired results are achieved.
Proper application is the responsibility of the user. Field visits by W. R. MEADOWS’ personnel are for the purpose of making technical recommendations only, and are not to supervise or provide quality control on the job-site.
Clean all tools and equipment after use with water.
Although this product has a low degree of hazard, the materials that it dissolves might be considered hazardous and should be disposed of according to all local, state and federal regulations.
SAFETY AND TOXICITY
Combustible mixture. Keep this product away from ignition sources. Can cause irritation of both skin and eyes. Wear chemical resistant gloves and glasses at all times. Harmful if swallowed. This product is for industrial and institutional use only by trained personnel. Keep out of reach of children.
Refer to Material Safety Data Sheet for complete health and safety information.
Section 03 01 30.51