SEAL CURE-30 – Concrete Curing and Sealing Compound

Product Data, W. R. MEADOWS

03 39 23

No. 375-A

Click for .PDF

SEAL CURE-30
Concrete Curing and Sealing Compound

DESCRIPTION
SEAL CURE-30 is a clear, 30% solids, UV-resistant, solvent-based, ready-to-use formula of acrylic copolymers and quick evaporating solvents, which cures, hardens,  seals,  and dustproofs  freshly placed and/or existing concrete.

USES
SEAL CURE-30 may be used on freshly placed and finished exterior concrete surfaces. It is ideal for use on concrete surfaces, sidewalks, parking decks, driveways, etc., or any place a higher sheen finish is desired.

For interior applications, specify and apply VOCOMP-30 curing and sealing compounds from W. R. MEADOWS.

FEATURES/BENEFITS

  • When properly applied, breathable film allows moisture in cured concrete to evaporate.
  • Provides a durable, tough, uniform, long-lasting film finish on exterior concrete surfaces.
  • Cures, hardens, dustproofs, and seals freshly placed concrete simultaneously in one application.
  • Minimizes hair-checking, cracking, dusting, spalling, and other defects common to improperly cured or uncured concrete.
  • Provides improved resistance to chemicals, oil, grease, de-icing salts
  • Applies easily … dries quickly for less downtime.

PACKAGING
5 Gallon Pails
55 Gallon Drums

COVERAGE
300 – 600 ft.2/gal. (7.4 – 14.7 m2/L).  Coverage may vary due to the texture and porosity of the substrate.

SHELF LIFE
When stored indoors in original, unopened containers at temperatures between 40° – 90° F, optimum performance and best use is obtained within two years of date of manufacture.

SPECIFICATIONS
ASTM C 1315, Type I, Class A
ASTM C 309, Type 1, Classes A & B
Dried film is USDA Accepted
U.S. EPA Architectural Coatings Rule

TECHNICAL DATA

Appearance Clear
Solids Content 30%
Weight/Gallon 7.7 lb.
Acid and Alkali  Resistance Good
Wearing Quality Good
VOC Content, g/L 664

All technical data is typical information, and may vary due to test methods, conditions and operator technique.

APPLICATION
Surface Preparation Existing (Old) Concrete: Concrete surface must be clean and dry with all stains, oil, grease, dust, and dirt removed prior to application. ULTRITE® DEGREASER from W. R. MEADOWS is recommended for cleaning.

New Concrete: SEAL CURE-30 should be applied when surface water has completely disappeared and the concrete surface will not be marred by walking workmen.

Application Method Use a sprayer, such as a Chapin 19049, or short-nap roller to apply a uniform film. Avoid puddling in low areas.  If puddles occur, brush or roll them out. A standard industrial-grade sprayer, equipped with a neoprene hose and gaskets, as well as a 0.5 GPM spray nozzle is recommended for best results.

For optimum performance, apply first coat at 600 ft.2/gal. After the first coat has thoroughly dried, apply a second coat at 600 ft.2/gal. NOTE: The second coat should be applied at a right angle.

Surface temperature of the concrete must be between 40° – 90° F.

Drying Time SEAL CURE-30 dries quickly. Drying times may be extended depending on application rate, temperature, humidity, and project conditions. Restrict foot traffic for at least four hours.  Twelve hours is preferable.

Cleanup Application equipment should be cleaned promptly after use with xylene or toluene.

PRECAUTIONS
Coating is to be applied without dilution or thinning.  FOR EXTERIOR USE ONLY. Block all HVAC ventilation ducts which may spread product odor.  Use with adequate ventilation and keep away from open flame.  If odor is objectionable, use of DECRA-SEAL W/B or the VOCOMP® series from W. R. MEADOWS is suggested.  Surfaces treated with SEAL CURE-30 may become slippery under certain conditions.  To increase slip resistance, add SURE-STEP additive from W. R. MEADOWS to the product.

SEAL CURE-30 should not be applied during high temperature conditions in direct sunlight. These conditions cause rapid evaporation, which does not allow the film to form properly. Under these conditions, the film may peel, bubble, and/or turn white (blush). SEAL CURE-30 should not be applied to concrete containing excessive moisture. Entrapped moisture in a solvent-based sealer may cause the film to peel and/or turn white (blush).

SEAL CURE-30 is a membrane-forming sealer.  All membrane-forming sealers may darken concrete or magnify imperfections caused by variations in the porosity and/or finishing of the concrete.

For any alternate adhesion specifications or requirements, besides ASTM C1315, Section 8.8, secure the approval of the  manufacturer of any paint, coating, carpet, adhesive, resilient flooring, floor topping, etc. (any type/composition of subsequent floor treatment) that will be applied over SEAL CURE-30.  Obtain this approval before applying the product over concrete previously applied with SEAL CURE-30.

HEALTH AND SAFETY
Prolonged inhalation of vapors in excess of permissible exposure limits may result in symptoms of transient central nervous system depression. Direct contact with the product may result in irritation of the skin and eyes. Product vapors may also cause irritation. SEAL CURE-30 is combustible. Remove ignition sources prior to use. Empty containers may hold combustible vapors. Handle empty containers as combustible liquids. In the event of a spill, contain the product; apply absorbents and place in sealed containers. In the event of a fire, contain all run-off water. Refer to Safety Data Sheet for complete health and safety information.

LEED INFORMATION
May help contribute to LEED credits:

  • MR Credit 2: Construction Waste Management
  • MR Credit 5: Regional Materials

2016-08

About W. R. MEADOWS

W. R. MEADOWS, INC. designs, manufactures, and markets high-quality building materials for today's construction professionals. Products are sold through an authorized distribution network. The family-owned and operated company focuses on product quality, exceptional service, and trusted integrity since its founding in 1926.
About Us | Vapor Barriers | Air Barriers | Concrete Expansion Joints | All Construction Products